TLC5929RGER

Texas Instruments
595-TLC5929RGER
TLC5929RGER

製造商:

說明:
LED照明驅動器IC 16-Ch Constant Crnt LED Driver A 595-TLC A 595-TLC5929RGET

ECAD模型:
下載免費的庫載入器,為ECAD工具轉換此文件。瞭解更多關於 ECAD 型號的資訊。

庫存量: 563

庫存:
563 可立即送貨
工廠前置作業時間:
6 週 工廠預計生產時間數量大於所顯示的數量。
最少: 1   多個: 1
單價:
NT$-.--
總價:
NT$-.--
估計關稅:
包裝:
完整捲(訂購多個3000)

Pricing (TWD)

數量 單價
總價
零卷 / MouseReel™
NT$63.00 NT$63.00
NT$46.44 NT$464.40
NT$42.12 NT$1,053.00
NT$37.44 NT$3,744.00
NT$35.21 NT$8,802.50
NT$33.88 NT$16,940.00
NT$32.80 NT$32,800.00
完整捲(訂購多個3000)
NT$31.39 NT$94,170.00
NT$30.74 NT$184,440.00
† NT$215.00 MouseReel™費用將加入您的購物車內並自動計算。所有MouseReel™訂單均不能取消和不能退換。

備用包裝

製造商 元件編號:
包裝:
Reel, Cut Tape, MouseReel
供貨情況:
庫存量
價格:
NT$78.12
最小值:
1

相似產品

Texas Instruments TLC5929RGET
Texas Instruments
LED照明驅動器IC 16-Ch Constant Crnt LED Driver A 595-TLC A 595-TLC5929RGER

商品屬性 屬性值 選擇屬性
Texas Instruments
產品類型: LED照明驅動器IC
RoHS:  
16 Output
Boost
50 mA
VQFN-24
5.5 V
3 V
33 MHz
10 V
TLC5929
- 40 C
+ 85 C
Constant Current, LED Open Detection, ON/OFF Control
Reel
Cut Tape
MouseReel
品牌: Texas Instruments
組裝國家: Not Available
擴散國: Not Available
原產國: MY
高電平輸出電流: - 2 mA
輸入電壓: 3 V to 5.5 V
低電平輸出電流: 2 mA
濕度敏感: Yes
安裝風格: SMD/SMT
通道數: 16 Channel
產品類型: LED Lighting Drivers
原廠包裝數量: 3000
子類別: Driver ICs
電源電流 - 最大值: 14 mA
每件重量: 54.600 mg
找到產品:
若要顯示類似商品,請選取至少一個核選方塊
至少選中以上一個核取方塊以顯示在此類別中類似的產品。
所選屬性: 0

此功能需要啟用JavaScript。

CNHTS:
8542319090
CAHTS:
8542390000
USHTS:
8542390090
JPHTS:
854239099
TARIC:
8542399000
MXHTS:
8542399901
ECCN:
EAR99

IS32LT3175N/P Single-Channel Linear LED Drivers

ISSI IS32LT3175N/P Single-Channel Linear LED Drivers come with fade in/out and PWM dimming. The regulators serve as a stand-alone LED driver-configurable from 20mA to 150mA with external resistors, no microcontroller is necessary. A logic level “courtesy light” signal from the PWM pin can be interfaced to precisely drive the LED channel. The IS32LT3175P obtains a positive polarity PWM signal. In addition, the IS32LT3175N obtains a negative polarity PWM signal. The regulator integrates a 63-step fade-in and fades out the algorithm (Gamma correction). This causes the output LED current to increasingly rise up to the full source value after the EN pin is pulsed.